Forum: Modifications, Repairs and Maintenance
08-17-2012, 05:06 PM
|
Replies: 2
Views: 2,324
Leak Check
You will need to do a leak check. It requires two people, one outside with a hose and one inside checking around the slide as water is sprayed onto the slide.
Lift the carpet up to be able to...
|
Forum: Modifications, Repairs and Maintenance
04-18-2012, 07:31 PM
|
Replies: 4
Views: 2,583
|
Forum: Modifications, Repairs and Maintenance
12-19-2011, 04:45 PM
|
Replies: 6
Views: 3,842
Battery Disconnect
It should by on when you are using or trailing the unit and off when you are storing the unit.
The battery is charged while towing, and when the unit is plugged into an outlet.
Dave
|
Forum: Fun Finder Community
12-12-2011, 04:32 PM
|
Replies: 12
Views: 15,660
Manual Slide
We cut two lengths slightly longer than the distance from the inside wall and the edge of the slide and wedged them in the sides towards the top of the slide. Just as a precaution we also laid two...
|
Forum: Modifications, Repairs and Maintenance
12-07-2011, 10:35 PM
|
Replies: 6
Views: 3,842
Battery Disconnect
Depending on the year of your unit it is on one of two locations on the FBS.
On the older units it is in the storage compartment on the passenger side just inside the compartment door on the left....
|
Forum: Fun Finder Community
12-07-2011, 10:19 PM
|
Replies: 12
Views: 15,660
Slide Out - Tough to move.
I have actually had to go through the process of moving the slide in on a cruiser product manually.
The wires from the controller were severed (owner created problem) and only one motor would...
|
Forum: Modifications, Repairs and Maintenance
12-03-2011, 12:37 PM
|
Replies: 6
Views: 3,305
Breakers and charging the battery
I concur with webslave.
The top breaker is the 30A main power, thus if it is not on the whole trailer will be disconnected from 110v power, and you will not charge the batteries because the...
|
Forum: Modifications, Repairs and Maintenance
12-02-2011, 10:45 PM
|
Replies: 4
Views: 3,148
Disconnect
The off position is pushed in and the on position is pulled out.
To clarify, the switch disconnects the battery from the trailer to prevent leaching of power from the battery to things like the LP...
|
Forum: Modifications, Repairs and Maintenance
12-02-2011, 10:36 PM
|
Replies: 6
Views: 3,305
Battery Charging
Are you saying that it will only charge with only those two breakers on and the rest off, or it will only charge with the two on and the rest either on or off?
|
Forum: Modifications, Repairs and Maintenance
12-02-2011, 10:29 PM
|
Replies: 6
Views: 3,294
Generator and charging batteries.
The assumption here is that you are starting the generator, plugging in the power cord from your trailer to the gen and then allowing the converter in the trailer to charge the batteries.
If this...
|
Forum: Fun Finder Community
11-12-2011, 06:08 PM
|
Replies: 3
Views: 4,838
TV Mount
There should be a bracket with a mounting plate with four small holes to be able to mount the tv with screws. If this is missing you will need find a suitable replacement. Contact your local...
|
Forum: Fun Finder Community
11-12-2011, 11:05 AM
|
Replies: 3
Views: 4,838
TV Size
They come with a 19" Sansui LED flat panel TV.
|
Forum: Modifications, Repairs and Maintenance
10-29-2011, 10:19 AM
|
Replies: 11
Views: 6,522
Water Heater
This is also common when the heater is full and there is not enough air in the top of the heater to accommodate the expansion of the water when it is being heated.
Check your H2O heater manual...
|
Forum: Modifications, Repairs and Maintenance
08-06-2011, 11:46 PM
|
Replies: 6
Views: 17,465
Replacement thermostat required
The thermostat needs to be replaced. The E2 error code you are getting is due to a temperature sensor in the thermostat. It is not really faulty, but the sensor is calibrated to low and in hot...
|
Forum: Modifications, Repairs and Maintenance
07-05-2011, 08:16 AM
|
Replies: 5
Views: 3,065
Stab Jack Motors
Yes you can move the stab jacks manually if you do not have power. Remove black plastic cap at the end of the motor and there is a nut on the end of the shaft that can be turned manually.
|